BOSTONSTANGS.COM

den83stng · den83stng

I have a 83 Hatchback. What year did the hinge or latch pin location change? I bought 90 doors and ran into this problem. I'm thinking 86 or 87 they changed?? Anybody know? Thanks.....

Steve the joker · Steve the joker

im trying to wire up the new gauges in my dash and im really confused on it, i have cables marked off, but i would like to kno if anyone thats wired in aftermarket gauges would stop in to help me wire them, or to give me some tips, thanks steve the joker

Justin89TT · Justin89TT

hey guys, i am having a problem with my msd box. its brand new and its the 6BTM.when i hook it up the car will run really rough for a couple minutes and then stall,when i try to restart it all it does is crank. i am getting spark when it cranks but it wont start.then when i disconnect it and run stock it starts ri...

droptopfox · droptopfox

i wana do my fuel cell in the ranger how do i plumb it to work it has 2 outlets and 2 vents ive never done one before

91notch · 91notch

Does anyone have a Trick Flow intake that also installed a strut tower brace. My car is a 1991. I'm looking for a brace that will work with a stock hood as well. Thanks.

DMURB · DMURB

im looking to get a new fuel pump. i was looking at summit. i was thinking about a trick flow 190 lph pump. does anyone have any input on these, what pumps do you like, let me know thanks guys

Takdashark · Takdashark

I see that MMR is a site sponsor, which is great. Im planning on ordering their mod 800 5.4 shortblock over the winter. Anyone have any good or bad things to say about them. So far i'v heard pretty good things. Thanks in advanced!!

Eightyfivefox · Eightyfivefox

Car has been leaking large amounts of oil it's coming from the bellhousing is this the rear main seal?? I don't want to pull it apart for no reason

91notch · 91notch

Got the car running after a 2 year redo of almost everything. The idle was adjusted and warmed up the motor for a bit. The problem came after about 2 miles. The motor started bucked in third, down shifted to 2nd and the same results. I think it might be a vaccum leak, but not sure. I barely made it home afte...

wheels · wheels

this is not for a mustang but for my 1999 jeep grand cherokee laredo... just bought the jeep this week manual say that it has a 20 gallon tank capacity i have gone to fill the tank 3 times already and can only fit 12 gallons. when i go to fill the gas light is on or it is below 1/4 tank..... what would cause th...

boostd710 · boostd710

Im looking for some new headlights, what do you guys think about these? anyone ever heard any bad things about them? My current headlights leak moisture into the housing and blow my headlight almost daily... If these are no good, what company sells good stock/clear headlights?

loopy · loopy

looking to get some 17x10's for the rear what is a good size tire. i was thinking of putting on Sumitomo HTR Z 315/35/17 how will this brand work thanks

supertukes · supertukes

just put long tubes and exhaust on my truck 94 f150. the tube that connected to the Y pipe i have no use for, i'd like to just delete the smog set up. anyone ever do this on a stang before? i know i have to block off the holes in the back of the head, but what else can go as far as sensors?

loopy · loopy

my car has had an issue sometimes it runs great, sometimes it hesitates. This past weekend I checked the plugs and re gapped them. set the ignition timing, changed the thermostat. It has another weird problem it doesnt start all the time, when i get it running and shut it down sometimes it dont start bac...

5p0inToH · 5p0inToH

anyone know where the cheapest place to get vp100 aditive is?

boostd710 · boostd710

I have a 1990 5.0. With the summer months aproaching, im starting to regret removing my A/C. What would i have to do to put working A/C back into my car? Would it cost a lot?

DMURB · DMURB

I'm wondering if anyone knows the torque specs on valve covers and my upper and lower intake manifold. Its a 306 with cobra upper and gt40 lower. Thanks a bunch

supertukes · supertukes

my g/f's lil bro got an 01 GT with bullitts, just wondering the widest tire he can fit on the rear. its got 245s now but i was wondering if 265-275s would fit...

droptopfox · droptopfox

my causins gt is havin issues the fuel pump wont stop running would it be a bad regulator

loopy · loopy

well the more i look over my motor the more i notice thing like i have no egr. What is egr for and do i need it. I have an egr spacer and theres an egr delete plate on back, does having egr give better mileage any info will be appreciated thanks.

FOXGT93 · FOXGT93

I have a 93 mustang gt, recently installed new spark plugs (duel platinum), wires, distribution cap, rotor, fuel filter, pcv valve. The timing is set. Running 93 octane (always). If I start the car up cold I experience throttle lag and can't accelerate that well. If the engine is warm I don't experi...

loopy · loopy

[url=http://cgi.ebay.com/ebaymotors/1987-88-89-90-91-SBF-FORD-289-302-DISTRIBUTOR-MUSTANG_W0QQitemZ350314705535QQcmdZViewItemQQptZMotors_Car_Truck_Parts_Accessories?hash=...

droptopfox · droptopfox

i want to put 3.5 wheel studs front and rear on my ranger so i can safly run a wheel spacer so i can run my center caps on my nice bullits im in the processes of putting a fox body rear converted to 5 lug in the rear so those studs are eisy but does anyone know if mustang wheels studs will work in the front ?

fast2000mustanggt · fast2000mustanggt

im looking for a harness if anyone can help im in hawaii so limited options i will pay the shipping ect, need both harnesses the one for the fuses in engine bay along with the fuel injector,throttle body, coil pack harness thanks

FOXGT93 · FOXGT93

Does anyone know where the blower resistor is located on a 2002 Mustang GT? I have the replacement resistor. I've been told it is located under the glove box? Is this correct? Is there anything I need to do to swap it out? Thanks, Brian

loopy · loopy

will bbk longtubes work with gt40p heads thanks? these stock shortys suck balls

331ci · 331ci

ANYBODY GOT A ROLL CAGE FOR A 92 VERT THEY WANT TO SELL?? OR AT LEAST A HOOP -- Edited by 331ci on Sunday 14th of March 2010 06:45:26 PM

loopy · loopy

well i am 6'3" tall i like to drive in a more upright position how can i modify my seat brackets to make them sit a lil lower. right know my head is a half inch from the roof. def needs to go a lil lower.

91chrisgt · 91chrisgt

does anybody have anyclue y every 2 weeks my starter solenoid shits the bed??? sometimes when i turn the key to start it will just keep turning over after its running ..........but after 2 weeks it just dies i replace it and its fine for a week or so then goes again wtf lol . getting pretty pricy seeing i dri...

Nunzio · Nunzio

Just wondering If anyone on here is willing to help me install these shorty headers, let me know if your interested, thx.

331ci · 331ci

anybody know where i can get a light bar for a 92 gt conv???

loopy · loopy

Hi everyone have a question if you could help me out when im on the highway doing about 70 everything is smooth when i go faster 80, 90, 100+ I get some vibration from under the car. Is that because of the aluminum drive shaft? would a drive shaft loop help out any? Also what should I set my timing to? thanks

hughezy91 · hughezy91

I was looking at exhaust and looking at the headers... Whats the advantages of shorties or longtubes... Thought somebody could tell me some pros and cons of both of them... thanks

kingrt86 · kingrt86

i am thinkng of buyin this motor for $1500 for everything what do you guys think thanks in advance the motor rebuilt zero miles!!! brand new top to bottom,bored .40 over,new high volume oil pump,new oil pan and pickup,FMS adjustable double roller timing chain,new timing cover and water pump,unde...

Takdashark · Takdashark

Scrib · Scrib

hey guys... not sure if anyones ever rebuilt a jet ski motor... its a 900 but its the first engine ive ever been in besides a small engine... when i took the head cover off the piston rings were bent so i pulled it apart and re did the rings... the engine had no compression in one cylinder so im guessing thi...

supertukes · supertukes

well, im going to be replacing the wheel joints in the axles on my f150 so im going to do the ball joints while i got it apart, anyone do these before? best way to do it? its a 94...

Scrib · Scrib

not sure if any of you have them but their pretty common so i figured id try... my girlfriends dad thinks his fuel pump is going... i dont want to get involved cuz i just dont... what do you guys think itll cost to replace-- pretty sure its a plastic tank so rust wouldnt be an issue

loopy · loopy

has anyone used a C&L Mass Air Meter before? are they godd or is there something better thanks.

hughezy91 · hughezy91

I have an 01 gt everything runs great on it. Only thing is the abs light goes on and off. I can hear the abs motor turn on, and i feel the abs in the pedal. It stops fine. Anybody got any ideas how to fix it or what may be wrong with it. Thanks

5.0 Hatch · 5.0 Hatch

So, my DD is a 1992 accord on wednesday I parked it and let it sit till yesterday go to start it nothing. Craanks over fast sounds like it wants to but nothing. So I pull a plug wire and notice the alot of oil had leaked down the cylinder of the plug. so I cleaned all the oil out of the cylinders and replaced the p...

howie8124 · howie8124

http://www.moddedmustangs.com/forums/96-98/143191-step-step-guide-installing-mark-viii-motor-96-gt.html

supertukes · supertukes

well im pretty happy with how my car is running right now, so its time for a suspension upgrade, not sure if i want lowering or not, i run 16" rims and will being going to 17" cobras soon i think. so im looking for something that is going to handle ok and be somewhat of a smooth ride, and look good, s...

boostd710 · boostd710

So the other day I take my car out for a ride and noticed that my Autometer tach is off from my factory tach by roughly 500rpm. My factory tach now is the accurate one where i thought the autometer one would be more accurate... When im idling at about 800rpm, the autometer tach reads about 1300-1400rpm. th...

boostd710 · boostd710

so the other day my outside passenger door handle broke, not off but no longer opens the door. Anyone want to put a new one on for me? I'll pay, quote me a price to do it... I'd attempt it, but have no clue how. thanks guys.

boostd710 · boostd710

My e-brake cable snapped on me the other day. Now when i drive, i hear a noise that could be the rear e-brake partially on, or the cable hanging on the driveshaft or something cause its only when the car is rolling. Not sure exactly what it is. I have never done an e-brake cable before, how do i do it? my car is...

LOWLIFES99 · LOWLIFES99

ok this is the deal i have a 1990 mustang gt convert i am trying to put stock struts with stock c/c plates and they will not fit i was told 87 to 89 & 90 to 93 are diffrent well i have tride both and nither fit please HELP ME figuer what the hell is wrong

bleed blue · bleed blue

just like the title says....which color is it on my ride 04 gt...i need to wire up my gauges and need to know this thanks

boostd710 · boostd710

I just got my car back today... I got a new starter put in after mine shit the bed and both starter bolts broke trying to get the old one out. The starter is a hi-torque mini starter from napa cost me $190+ labor to get the broken bolts drilled out of the bellhousing. So the starter works great and fires my c...

DMURB · DMURB

i was going to install an electric fan in my fox. I dont have the relay for it to turn on and off automatically so i was just going to put it on a togle switch. But my question is should i put it on a fuse. And if so how do i wire that up battery to switch, switch to fuse, fuse to fan? Thanks for the help

Topic		Started By	Replies	Views	Last Post
	Door fitment Question 83 (Preview) I have a 83 Hatchback. What year did the hinge or latch pin location change? I bought 90 doors and ran into this problem. I'm thinking 86 or 87 they changed?? Anybody know? Thanks.....	den83stng	4	874	Jul 25, 2010 by den83stng
	gauge wiring (Preview) im trying to wire up the new gauges in my dash and im really confused on it, i have cables marked off, but i would like to kno if anyone thats wired in aftermarket gauges would stop in to help me wire them, or to give me some tips, thanks steve the joker	Steve the joker	1	822	Jul 15, 2010 by T76 Cobra
	help with msd6 btm (Preview) hey guys, i am having a problem with my msd box. its brand new and its the 6BTM.when i hook it up the car will run really rough for a couple minutes and then stall,when i try to restart it all it does is crank. i am getting spark when it cranks but it wont start.then when i disconnect it and run stock it starts ri...	Justin89TT	7	878	Jul 12, 2010 by luke
	fuel cell install (Preview) i wana do my fuel cell in the ranger how do i plumb it to work it has 2 outlets and 2 vents ive never done one before	droptopfox	5	872	Jul 8, 2010 by Mcnally351
	STRUT TOWER BRACE AND TRICK FLOW INTAKE (Preview) Does anyone have a Trick Flow intake that also installed a strut tower brace. My car is a 1991. I'm looking for a brace that will work with a stock hood as well. Thanks.	91notch	2	1187	Jul 8, 2010 by luke
	fuel pump (Preview) im looking to get a new fuel pump. i was looking at summit. i was thinking about a trick flow 190 lph pump. does anyone have any input on these, what pumps do you like, let me know thanks guys	DMURB	6	903	Jul 6, 2010 by flamingpony83
	MMR (Preview) I see that MMR is a site sponsor, which is great. Im planning on ordering their mod 800 5.4 shortblock over the winter. Anyone have any good or bad things to say about them. So far i'v heard pretty good things. Thanks in advanced!!	Takdashark	46	2175	Jun 10, 2010 by Takdashark
	Oil leak problem ( 1 2 ) (Preview) Car has been leaking large amounts of oil it's coming from the bellhousing is this the rear main seal?? I don't want to pull it apart for no reason	Eightyfivefox	53	2802	Jun 10, 2010 by Eightyfivefox
	Bucking issues (Preview) Got the car running after a 2 year redo of almost everything. The idle was adjusted and warmed up the motor for a bit. The problem came after about 2 miles. The motor started bucked in third, down shifted to 2nd and the same results. I think it might be a vaccum leak, but not sure. I barely made it home afte...	91notch	16	1292	Jun 1, 2010 by 91notch
	FUEL TANK ISSUE (Preview) this is not for a mustang but for my 1999 jeep grand cherokee laredo... just bought the jeep this week manual say that it has a 20 gallon tank capacity i have gone to fill the tank 3 times already and can only fit 12 gallons. when i go to fill the gas light is on or it is below 1/4 tank..... what would cause th...	wheels	5	913	May 29, 2010 by Purplestang96
	what do you guys think about these headlights? (Preview) Im looking for some new headlights, what do you guys think about these? anyone ever heard any bad things about them? My current headlights leak moisture into the housing and blow my headlight almost daily... If these are no good, what company sells good stock/clear headlights?	boostd710	14	1258	May 18, 2010 by 88mustangt
	tire size (Preview) looking to get some 17x10's for the rear what is a good size tire. i was thinking of putting on Sumitomo HTR Z 315/35/17 how will this brand work thanks	loopy	15	1095	May 18, 2010 by Eightyfivefox
	smog delete (Preview) just put long tubes and exhaust on my truck 94 f150. the tube that connected to the Y pipe i have no use for, i'd like to just delete the smog set up. anyone ever do this on a stang before? i know i have to block off the holes in the back of the head, but what else can go as far as sensors?	supertukes	2	947	May 14, 2010 by supertukes
	been having some problems with the 89 ( 1 2 ) (Preview) my car has had an issue sometimes it runs great, sometimes it hesitates. This past weekend I checked the plugs and re gapped them. set the ignition timing, changed the thermostat. It has another weird problem it doesnt start all the time, when i get it running and shut it down sometimes it dont start bac...	loopy	80	3650	May 11, 2010 by loopy
	local place to buy vp100 (Preview) anyone know where the cheapest place to get vp100 aditive is?	5p0inToH	0	773	May 3, 2010 by 5p0inToH
	air conditioning (Preview) I have a 1990 5.0. With the summer months aproaching, im starting to regret removing my A/C. What would i have to do to put working A/C back into my car? Would it cost a lot?	boostd710	6	983	May 2, 2010 by Mustang5L5
	torque specs (Preview) I'm wondering if anyone knows the torque specs on valve covers and my upper and lower intake manifold. Its a 306 with cobra upper and gt40 lower. Thanks a bunch	DMURB	5	862	May 2, 2010 by 90stangGT
	2001 GT tire fitment (Preview) my g/f's lil bro got an 01 GT with bullitts, just wondering the widest tire he can fit on the rear. its got 245s now but i was wondering if 265-275s would fit...	supertukes	11	981	Apr 29, 2010 by Mustang5L5
	90 gt fuel issue (Preview) my causins gt is havin issues the fuel pump wont stop running would it be a bad regulator	droptopfox	6	960	Apr 16, 2010 by droptopfox
	?'s about EGR (Preview) well the more i look over my motor the more i notice thing like i have no egr. What is egr for and do i need it. I have an egr spacer and theres an egr delete plate on back, does having egr give better mileage any info will be appreciated thanks.	loopy	7	879	Apr 10, 2010 by Mustang5L5
	Throttle lag after cold start? (Preview) I have a 93 mustang gt, recently installed new spark plugs (duel platinum), wires, distribution cap, rotor, fuel filter, pcv valve. The timing is set. Running 93 octane (always). If I start the car up cold I experience throttle lag and can't accelerate that well. If the engine is warm I don't experi...	FOXGT93	5	893	Apr 9, 2010 by Mustang5L5
	question about pro comp distributors (Preview) [url=http://cgi.ebay.com/ebaymotors/1987-88-89-90-91-SBF-FORD-289-302-DISTRIBUTOR-MUSTANG_W0QQitemZ350314705535QQcmdZViewItemQQptZMotors_Car_Truck_Parts_Accessories?hash=...	loopy	3	1090	Apr 6, 2010 by droptopfox
	non mustang wheel studs ? (Preview) i want to put 3.5 wheel studs front and rear on my ranger so i can safly run a wheel spacer so i can run my center caps on my nice bullits im in the processes of putting a fox body rear converted to 5 lug in the rear so those studs are eisy but does anyone know if mustang wheels studs will work in the front ?	droptopfox	2	844	Apr 5, 2010 by qwik88
	96-97 cobra harness (Preview) im looking for a harness if anyone can help im in hawaii so limited options i will pay the shipping ect, need both harnesses the one for the fuses in engine bay along with the fuel injector,throttle body, coil pack harness thanks	fast2000mustanggt	0	705	Mar 29, 2010 by fast2000mustanggt
	2002 Mustang GT Blower Resistor Question (Preview) Does anyone know where the blower resistor is located on a 2002 Mustang GT? I have the replacement resistor. I've been told it is located under the glove box? Is this correct? Is there anything I need to do to swap it out? Thanks, Brian	FOXGT93	4	854	Mar 21, 2010 by FOXGT93
	questions about bbk longtubes (Preview) will bbk longtubes work with gt40p heads thanks? these stock shortys suck balls	loopy	11	2173	Mar 17, 2010 by Mustang5L5
	ANYBODY GOT A ROLL CAGE FOR A 92 VERT??? (Preview) ANYBODY GOT A ROLL CAGE FOR A 92 VERT THEY WANT TO SELL?? OR AT LEAST A HOOP -- Edited by 331ci on Sunday 14th of March 2010 06:45:26 PM	331ci	1	873	Mar 15, 2010 by Mcnally351
	question about seat height (Preview) well i am 6'3" tall i like to drive in a more upright position how can i modify my seat brackets to make them sit a lil lower. right know my head is a half inch from the roof. def needs to go a lil lower.	loopy	6	816	Mar 13, 2010 by loopy
	STARTER SOLENOID WTF?????!!! (Preview) does anybody have anyclue y every 2 weeks my starter solenoid shits the bed??? sometimes when i turn the key to start it will just keep turning over after its running ..........but after 2 weeks it just dies i replace it and its fine for a week or so then goes again wtf lol . getting pretty pricy seeing i dri...	91chrisgt	22	1375	Mar 10, 2010 by jgt8229
	98 GT BBK Shorty Header Install help (Preview) Just wondering If anyone on here is willing to help me install these shorty headers, let me know if your interested, thx.	Nunzio	0	822	Mar 9, 2010 by Nunzio
	light bar for 92 conv.???? (Preview) anybody know where i can get a light bar for a 92 gt conv???	331ci	7	911	Mar 8, 2010 by Gina
	Vibration after 70-80 mph (Preview) Hi everyone have a question if you could help me out when im on the highway doing about 70 everything is smooth when i go faster 80, 90, 100+ I get some vibration from under the car. Is that because of the aluminum drive shaft? would a drive shaft loop help out any? Also what should I set my timing to? thanks	loopy	20	1270	Mar 7, 2010 by Mustang5L5
	SHORTIE HEADERS VS LONGTUBE (Preview) I was looking at exhaust and looking at the headers... Whats the advantages of shorties or longtubes... Thought somebody could tell me some pros and cons of both of them... thanks	hughezy91	9	908	Mar 4, 2010 by Timbo8650
	thinking of purchasing new motor.....feedback please (Preview) i am thinkng of buyin this motor for $1500 for everything what do you guys think thanks in advance the motor rebuilt zero miles!!! brand new top to bottom,bored .40 over,new high volume oil pump,new oil pan and pickup,FMS adjustable double roller timing chain,new timing cover and water pump,unde...	kingrt86	1	862	Feb 28, 2010 by jgt8229
	New seats in :-) (Preview)	Takdashark	25	1886	Feb 22, 2010 by loopy
	jey ski motor (Preview) hey guys... not sure if anyones ever rebuilt a jet ski motor... its a 900 but its the first engine ive ever been in besides a small engine... when i took the head cover off the piston rings were bent so i pulled it apart and re did the rings... the engine had no compression in one cylinder so im guessing thi...	Scrib	0	710	Feb 18, 2010 by Scrib
	f150 ball joints (Preview) well, im going to be replacing the wheel joints in the axles on my f150 so im going to do the ball joints while i got it apart, anyone do these before? best way to do it? its a 94...	supertukes	0	678	Feb 15, 2010 by supertukes
	01 toyota fuel pump (Preview) not sure if any of you have them but their pretty common so i figured id try... my girlfriends dad thinks his fuel pump is going... i dont want to get involved cuz i just dont... what do you guys think itll cost to replace-- pretty sure its a plastic tank so rust wouldnt be an issue	Scrib	2	752	Feb 13, 2010 by Scrib
	mass air (Preview) has anyone used a C&L Mass Air Meter before? are they godd or is there something better thanks.	loopy	0	730	Feb 9, 2010 by loopy
	ABS Problem (Preview) I have an 01 gt everything runs great on it. Only thing is the abs light goes on and off. I can hear the abs motor turn on, and i feel the abs in the pedal. It stops fine. Anybody got any ideas how to fix it or what may be wrong with it. Thanks	hughezy91	4	788	Jan 20, 2010 by hughezy91
	1992 Honda Accord No Start? (Preview) So, my DD is a 1992 accord on wednesday I parked it and let it sit till yesterday go to start it nothing. Craanks over fast sounds like it wants to but nothing. So I pull a plug wire and notice the alot of oil had leaked down the cylinder of the plug. so I cleaned all the oil out of the cylinders and replaced the p...	5.0 Hatch	10	2119	Dec 30, 2009 by Mineral 02
	Mark VIII motor in a 96+ GT (Preview) http://www.moddedmustangs.com/forums/96-98/143191-step-step-guide-installing-mark-viii-motor-96-gt.html	howie8124	6	1015	Dec 27, 2009 by T76 Cobra
	spring question / opinion (Preview) well im pretty happy with how my car is running right now, so its time for a suspension upgrade, not sure if i want lowering or not, i run 16" rims and will being going to 17" cobras soon i think. so im looking for something that is going to handle ok and be somewhat of a smooth ride, and look good, s...	supertukes	7	1033	Nov 23, 2009 by Green92LX
	Autometer Tach Problem (Preview) So the other day I take my car out for a ride and noticed that my Autometer tach is off from my factory tach by roughly 500rpm. My factory tach now is the accurate one where i thought the autometer one would be more accurate... When im idling at about 800rpm, the autometer tach reads about 1300-1400rpm. th...	boostd710	5	890	Nov 4, 2009 by Gotyourcamper
	broken passener door handle. Anyone want to help me out? (Preview) so the other day my outside passenger door handle broke, not off but no longer opens the door. Anyone want to put a new one on for me? I'll pay, quote me a price to do it... I'd attempt it, but have no clue how. thanks guys.	boostd710	13	930	Nov 2, 2009 by boostd710
	E-brake cable snapped (Preview) My e-brake cable snapped on me the other day. Now when i drive, i hear a noise that could be the rear e-brake partially on, or the cable hanging on the driveshaft or something cause its only when the car is rolling. Not sure exactly what it is. I have never done an e-brake cable before, how do i do it? my car is...	boostd710	8	859	Oct 25, 2009 by wheels
	haveing strut caster camber instaling problem (Preview) ok this is the deal i have a 1990 mustang gt convert i am trying to put stock struts with stock c/c plates and they will not fit i was told 87 to 89 & 90 to 93 are diffrent well i have tride both and nither fit please HELP ME figuer what the hell is wrong	LOWLIFES99	1	782	Oct 24, 2009 by wheels
	dimmer switch wire (Preview) just like the title says....which color is it on my ride 04 gt...i need to wire up my gauges and need to know this thanks	bleed blue	13	896	Oct 14, 2009 by T76 Cobra
	Just got my car back... Starter Issue, advice neededdd (Preview) I just got my car back today... I got a new starter put in after mine shit the bed and both starter bolts broke trying to get the old one out. The starter is a hi-torque mini starter from napa cost me $190+ labor to get the broken bolts drilled out of the bellhousing. So the starter works great and fires my c...	boostd710	3	807	Oct 13, 2009 by forcefednotch
	electric fan wiring (Preview) i was going to install an electric fan in my fox. I dont have the relay for it to turn on and off automatically so i was just going to put it on a togle switch. But my question is should i put it on a fuse. And if so how do i wire that up battery to switch, switch to fuse, fuse to fan? Thanks for the help	DMURB	6	812	Oct 12, 2009 by DMURB
«First < 1 2 3 4 … 8 > Last» \| Page of 8 sorted by