BOSTONSTANGS.COM

flamingpony83 · flamingpony83

car is bucking when im not giving it a good amount of gas. could this be fuel pressure?? i am getting 40psi when idle. i changed my maf from a 73mm to a 90mm. any help is appreciated.

stang1990 · stang1990

im buying a set off lowering for my 90 fox and i like to know if anybody can tell me how to install them thanks,Jose -- Edited by stang1990 at 06:37, 2008-10-08

91chrisgt · 91chrisgt

my car is a carbd 302 , i have a 750 edlbrock carb and a trickflow stage 2 cam what should i be running for fuel pressure? thanks , chris

93fox · 93fox

i just fired up my mustang after finishin the turbo install and it was running pretty good idlein at about 1100-1200rpm then it all of the sudden shut off. im running a msd btm and blaster coil. i by passed the msd box and still nothing any ideas? thanks in advance Thrasher

Geevaaa9112 · Geevaaa9112

My car has a high pitched whistle noise while i give it about 1/2 throttle in any gear, then it will go away. I have checked for vac leaks, cleaned the MAF and throttle body, put in a new pcv valve, new air filter, and the new intake gasket seems to be in place. I actually have more vacuum pressure then i did be...

mustang50lx88 · mustang50lx88

I am planning on removing my old pass side door and was wondering if I had to take the fender off in order to remove the door properly? And what steps need to be taken in order to remove the door from the hinge? Thanks for the help.. I greatly appreciate it. -- Edited by mustang50lx88 at 11:1...

flamingpony83 · flamingpony83

what is the middle port of the lower intake. exaust? if so do you need it or can i plug it? it is causing a whole world of problems for me. i got a bread box intake and it fits a gt40 lower, problem is it doesnt cover that middle port. dont know what my options are..... -- Edited by flamingpony83 at 17:37, 2008-...

boostd710 · boostd710

So i am looking at this 88 notch. Its got a 306 with JE pistons that was rebuilt about 20K ago. Im just nervious because it has a ZEX nitrous kit with purge. Im wondering if there is anyway to see if the motor has been damaged with having to pull it apart. I dont want to get a car with a blown motor, or a motor that...

supertukes · supertukes

my gas tank is very pressurized for some reason, when i take the gas cap off, air comes out of the filler....any ideas?

bleed blue · bleed blue

looking for some info on aftermarket heads for the 4.6 i have heard that the patriot heads are shit dont know why thats just what i here tell me diffrent are recommend something different i will also br doing cams at the same time

sem76 · sem76

So my car's been doing this for a few weeks now. About a month ago a friend and I put 390 Motive gears (ya I know not Ford Racing) and got the proper backlash at .011 and ect... Did the breakin procedure correctly. The gears seemed fine until a few days later we all decide to go down to NED and pulling onto 93 wi...

mikefheath87 · mikefheath87

ive had this problem for a couple of days. the car runs and drives fine except it will stall on deceleration or idle. sometimes it even makes a really terrible hissing sound form the air intake. sometimes it will pop an engine light and really run crappy...i cannot retrieve any non emission codes. most...

stang1990 · stang1990

How hard is it and what do I need to convert it.1990 lx 5.0 if you need to know that. is for my father in law he wants to convert his efi to carb what can i do and what intake and carb to i need, i know some off you like efi but is not my stang im keeping mine efi so can anybody help thanks.

Geevaaa9112 · Geevaaa9112

Just finished my car and with the new rims its too low with eibach pro-kit springs. Any suggestions on springs that are less dramatic of a drop but have a good stance. I was looking at the ford racing springs that are 7/8" drop. Any input is greatly appreciated. Thanks

91chrisgt · 91chrisgt

when driving at low speeds car jerks and seems like it bogs down , when i give it steady gas it clears and doesn't jerk/bog as much , if i'm driving in afternoon traffic doing between 10-35 with little gas pedal seems to be the problem and it is fucking annoying !!!almost makes me want to say fuck this thing...

fuck bostonstangs · fuck bostonstangs

pulled my wheel just now to see if i can stop the squeak i have been hearing for a while and its driving me nuts. Come to find out it is becuase mustangs suck. I can grab my studs and move them in and out off the axel, not much but enough that it lets the rotor move and its causing the squeak, the drivers side is ti...

FoxStang93 · FoxStang93

doubt anyone on here has done it...but has anyone seen any write ups on it or seen someone who has done it?

andyss420 · andyss420

was looking at a x cam. i have a 94 cobra and was searching around and found a site that said all i needed was a x can and the trick flow spring kit for my gt40's, and i wouldn't have any valve to piston issues. Duration: 224°/224° @ .050'' Lift: .542''/.542'' Trans: 5-Speed Notes: Fair Idle, Excellent...

cobraman24 · cobraman24

Bridgestone Potenza 285/40 ZR17 just what to make sure these will fit my cobra my rims are 17x9 the tires are for 17x 9.5-10. just what some input and see what everyone thinks

stang1990 · stang1990

hi! guys i dont know much about mustang i just love the way the sound but i like to do a f cam what would i have to do without spending so much money i have a 90 with a stock 5.0 motor what do you think, i like the way it sounds i like to scared little hondas around so let me know

FoxStang93 · FoxStang93

I need to take out the part in the rear above my back seat in the interior...i tried taking the seat belt things of but couldnt even get those...plus it was like 100 degrees out and i was sweaty and just didnt wanna bother with it lol...

supertukes · supertukes

who in here runs an F cam? im havin a little trouble gettin my car to "go" it will start and idle fine, as soon as i give it some gas it hesitates and stalls...... not sure if timing is set right maybe its the carb.....any ideas?

FoxStang93 · FoxStang93

been searching for days now on an article on a DIY TT set up with the two T3 turbos i have...nobody on turbomustangs.com wants to help...they basically say fuck ya self and search...but have gone through almost 50 pages of posts and found nothing...didnt know if anyone knows of any other turbo mustang...

moddedstang1320 · moddedstang1320

alright well im thinking about doing the comp XE270AH cams, or cushman stage II cams(used to be VT cams) this winter if they are worth it and possibly a pair of patriot cylinder heads as well if i save up enough money. anyone know if its worth spending the 2k on these. since im in college my parents dont wan...

fuck bostonstangs · fuck bostonstangs

I have decided to go with Powerslot rotors and hawk pads. Is it worth the extra $15 to buy the ceramic pads vs. the HPS??? They say the ceramic make less dust, and quieter. What would you do?

93fox · 93fox

anyone every intall one of these i got the narrow band i have to hook up the purple wire to one of the o2 sensor wires wat wires did you guys use thanks

YoLa · YoLa

anybody in here got a clue why i bent my stock pushrods, i just threw on a set of GT40 heads on my 88 GT using stock HO cam, with cobra upper and lower intake, crane cams cobra 1.7 RR's, the heads are stock valves etc, the springs are new comp cams rated for .550, i threw them on with the stock rods and bent'em. i...

5pointslow · 5pointslow

to get my 460 punched 030 over cam bearings cleaned freeze plugs align honed decked 900$ or do guys have any other suggestions who might be cheaper this is presician in dighton ma but im in taunton thanks

9T9MnyPit · 9T9MnyPit

hey guys just swapped over to a UPR O/R X-pipe with the MIL's and this code popped up after 350 miles of driving it with the set-up, the codes reads P0430 Catalyst System Efficiency below Limit - Bank No 2.? is my O2 sensor shot? there are no leaks in the exhaust??? doesnt make any sense since i used to have t...

stang1990 · stang1990

hi guys i have a 1990 5.0 i want to port my lower intake can anybody tell how and what tools i can used i dont have a air compressor but i heard you can used a dremel tool but what else i need i want to do it myself, thanks guys. -- Edited by stang1990 at 23:20, 2008-09-09

wheels · wheels

was driving and powersteering was getting crappy check fluids toped off any hints or ideas pump was replaced by ford in march 06 20k on pump HELP!!!!!!!!!!!!!!

YoLa · YoLa

Is there any programs out there you can run on a laptop through your stock computer? Any help with this one guys?

wild88stang · wild88stang

Any members out there changed there fuel lines to the braided lines? Well my 88 lx fuel line rotted away and need to install new lines but not sure on how to approach this problem. Braided lines or getting ss stock fuel line and bend myself????? Russell performance has line but not sure with all fittings...

fuck bostonstangs · fuck bostonstangs

OK. After doing research and talking to members I have decided to get the Powerslot Silve Cadium Plated (non rusting/corrosion) Front AND Rear from American Muscle AND Hawk HPS (High Performance Street) Brake Pads Front and Rear from American Muscle All together with my discount I would be spendin...

mikefheath87 · mikefheath87

i have a cam that i dont know what it is it has numbers 1206 on the front and after the distributoe gear it says ZE is this stock ....im putting my motor together and im either gonna use this or the crower 15512 cam

mikefheath87 · mikefheath87

can i run stock rockers on theese heads without problems? i want to use stock vcalve covers and these rockers will not fit at all i know the cutout trick its not happening on these rockers. what are the disadvantages i will run into?

mikefheath87 · mikefheath87

just bought a motor. guy siad it was a 306 but its not. it has a crowler 15512. anyone have them how are they? am i beter off with anything elce? i hope this one works well for what i have... cobra intake gt40 heads 24lb inj.

uatlb · uatlb

Found this and had to share........ Step 1: go to http://www.bedlib.org/ebsco.html Step 2: click on the ARRC logo near the top Step 3: under "user id" type "user" and under "password" type "password" Step 4: scroll to the bottom, and press the AAR...

mikefheath87 · mikefheath87

ok guys i finally got the s trim and i want to install it on my pos motor for about a months or two....i still need bigger inj so if anyone has em let me know. so for those of you who have done this any heads up on something specific on what i should or shouldn't do. Any input is greatly appreciated. -- Edited by m...

TAPorSNAP · TAPorSNAP

I finally got all the parts i needed and installed them. New head gaskets, upper and lower intake water pump, and headers. I just got it all 2gether about 20 min ago and when the car starts its knocking and shaking like a bastard. any ideas on whats up with it

FoxStang93 · FoxStang93

After talkin to a few people it seems a 351 project into a 408 stroker seems to be the way i want to go and its the most realistic goal i can reach right now...what do i need to do as far as motor mounts...tranni...intake...carb...all that stuff...thanks

bleed blue · bleed blue

so last night very long night i installed a or h pipe and a cat back and now wheni come to a stop the idle stays at about 1k for a couple of seconds i have yet to put the mil elims in caise i needed extensions for the o2's so is it cause the ses light is or else what do i do here thanks

5pointslow · 5pointslow

thanks to all on tech questions about it even know i got to prove to half of u guys that it will work lol jk guys thanx a bunch once lifts in everyone welcome to use

5pointslow · 5pointslow

need to get an idea on front springs ...laugh 460 i know blah blah hope u guys respect my plans because i would do the same to you guys and i want to be alittle diffrent thanks again mineral02,retro5.0,12second5.0 aka larry for all the help with my dumb ass -- Edited by 5pointslow at 17:36, 2008-07-17 -- E...

5pointslow · 5pointslow

efi stock block 302 turbo carb but same as above or 351 windsor to 408 carb with turbo or go same with efi or fuck it just slap a 460 and c6 in it and throw the a 250 shot of spray whats your guys opinions got money to do any way not gonna be daily driven an is gonna be an auto a week end car to beat on put my foot throug...

andyss420 · andyss420

i have a 94 cobra with gt40 heads on it and some 1.7's. looking at patriot performance aluminum heads but want to know what size i should get. don't want to really cut pistons and don't want to order get and install to find out i have clearence isues. a set of heads are under $1000. i know someone with then an...

mikefheath87 · mikefheath87

the numbers on the lower sprocket...302 w/crowler 15512 set it at the original timing mark or advance or retard anything? the sprocket is labeled all the way around. car is going to be s/c. anything helps thanks.

fuck bostonstangs · fuck bostonstangs

Within the next month I am due for new brakes and rotors. I have heard many different things. I am looking for drilled and slotted rotors that DON'T RUST, along with decent brake pads. Anyone have any advice on which to buy? Which NOT to buy? I would not like to spend a ton of money on them but at the same time...

bleed blue · bleed blue

which heads are better or id there even a difference the romeo or windsor all i know right now is the valve covers are diffrent

bleed blue · bleed blue

what can a stock 2v hod for hp and boost i would like to supercharge it but dont want to pop it so what are some safe numbers and what kind of power am i looking also would like to do it as a complete kit

Topic		Started By	Replies	Views	Last Post
	another fuel pressure question. (Preview) car is bucking when im not giving it a good amount of gas. could this be fuel pressure?? i am getting 40psi when idle. i changed my maf from a 73mm to a 90mm. any help is appreciated.	flamingpony83	2	545	Oct 5, 2008 by Geevaaa9112
	can anybody tell how to installed lowering spring on a 87-93 fox(closed) (Preview) im buying a set off lowering for my 90 fox and i like to know if anybody can tell me how to install them thanks,Jose -- Edited by stang1990 at 06:37, 2008-10-08	stang1990	10	617	Oct 4, 2008 by snakebite
	FUEL PRESSURE? (Preview) my car is a carbd 302 , i have a 750 edlbrock carb and a trickflow stage 2 cam what should i be running for fuel pressure? thanks , chris	91chrisgt	12	558	Oct 1, 2008 by supertukes
	no spark need help asap (Preview) i just fired up my mustang after finishin the turbo install and it was running pretty good idlein at about 1100-1200rpm then it all of the sudden shut off. im running a msd btm and blaster coil. i by passed the msd box and still nothing any ideas? thanks in advance Thrasher	93fox	10	579	Sep 30, 2008 by Mineral 02
	Whistling under load (Preview) My car has a high pitched whistle noise while i give it about 1/2 throttle in any gear, then it will go away. I have checked for vac leaks, cleaned the MAF and throttle body, put in a new pcv valve, new air filter, and the new intake gasket seems to be in place. I actually have more vacuum pressure then i did be...	Geevaaa9112	13	822	Sep 30, 2008 by Geevaaa9112
	Removing Doors on a Fox Mustang (Preview) I am planning on removing my old pass side door and was wondering if I had to take the fender off in order to remove the door properly? And what steps need to be taken in order to remove the door from the hinge? Thanks for the help.. I greatly appreciate it. *-- Edited by mustang50lx88 at 11:1...*	mustang50lx88	14	611	Sep 30, 2008 by mustang50lx88
	Question for the techy's (Preview) what is the middle port of the lower intake. exaust? if so do you need it or can i plug it? it is causing a whole world of problems for me. i got a bread box intake and it fits a gt40 lower, problem is it doesnt cover that middle port. dont know what my options are..... -- Edited by flamingpony83 at 17:37, 2008-...	flamingpony83	5	593	Sep 29, 2008 by flamingpony83
	Question about motor in notchback... (Preview) So i am looking at this 88 notch. Its got a 306 with JE pistons that was rebuilt about 20K ago. Im just nervious because it has a ZEX nitrous kit with purge. Im wondering if there is anyway to see if the motor has been damaged with having to pull it apart. I dont want to get a car with a blown motor, or a motor that...	boostd710	7	648	Sep 22, 2008 by 5pointslow
	gas tank question (Preview) my gas tank is very pressurized for some reason, when i take the gas cap off, air comes out of the filler....any ideas?	supertukes	5	543	Sep 21, 2008 by Mustang5L5
	4.6 heads (Preview) looking for some info on aftermarket heads for the 4.6 i have heard that the patriot heads are shit dont know why thats just what i here tell me diffrent are recommend something different i will also br doing cams at the same time	bleed blue	6	626	Sep 19, 2008 by LX546
	vibration at higher speeds (Preview) So my car's been doing this for a few weeks now. About a month ago a friend and I put 390 Motive gears (ya I know not Ford Racing) and got the proper backlash at .011 and ect... Did the breakin procedure correctly. The gears seemed fine until a few days later we all decide to go down to NED and pulling onto 93 wi...	sem76	21	1104	Sep 19, 2008 by sem76
	stalling problem (Preview) ive had this problem for a couple of days. the car runs and drives fine except it will stall on deceleration or idle. sometimes it even makes a really terrible hissing sound form the air intake. sometimes it will pop an engine light and really run crappy...i cannot retrieve any non emission codes. most...	mikefheath87	7	600	Sep 18, 2008 by mikefheath87
	re;efi to carb swap (Preview) How hard is it and what do I need to convert it.1990 lx 5.0 if you need to know that. is for my father in law he wants to convert his efi to carb what can i do and what intake and carb to i need, i know some off you like efi but is not my stang im keeping mine efi so can anybody help thanks.	stang1990	9	583	Sep 16, 2008 by Big Frank
	Springs (Preview) Just finished my car and with the new rims its too low with eibach pro-kit springs. Any suggestions on springs that are less dramatic of a drop but have a good stance. I was looking at the ford racing springs that are 7/8" drop. Any input is greatly appreciated. Thanks	Geevaaa9112	0	475	Sep 15, 2008 by Geevaaa9112
	what is wrong with my car? (Preview) when driving at low speeds car jerks and seems like it bogs down , when i give it steady gas it clears and doesn't jerk/bog as much , if i'm driving in afternoon traffic doing between 10-35 with little gas pedal seems to be the problem and it is fucking annoying !!!almost makes me want to say fuck this thing...	91chrisgt	9	644	Sep 14, 2008 by FoxStang93
	wtf, if its not one thing its another.... (Preview) pulled my wheel just now to see if i can stop the squeak i have been hearing for a while and its driving me nuts. Come to find out it is becuase mustangs suck. I can grab my studs and move them in and out off the axel, not much but enough that it lets the rotor move and its causing the squeak, the drivers side is ti...	fuck bostonstangs	5	640	Sep 14, 2008 by fuck bostonstangs
	SN-95 dash in fox body? (Preview) doubt anyone on here has done it...but has anyone seen any write ups on it or seen someone who has done it?	FoxStang93	8	1983	Sep 14, 2008 by WETDRM
	will it fit (Preview) was looking at a x cam. i have a 94 cobra and was searching around and found a site that said all i needed was a x can and the trick flow spring kit for my gt40's, and i wouldn't have any valve to piston issues. Duration: 224°/224° @ .050'' Lift: .542''/.542'' Trans: 5-Speed Notes: Fair Idle, Excellent...	andyss420	5	603	Sep 12, 2008 by Pitbull11
	will these fit (Preview) Bridgestone Potenza 285/40 ZR17 just what to make sure these will fit my cobra my rims are 17x9 the tires are for 17x 9.5-10. just what some input and see what everyone thinks	cobraman24	8	571	Sep 12, 2008 by FoxStang93
	f-cam question (Preview) hi! guys i dont know much about mustang i just love the way the sound but i like to do a f cam what would i have to do without spending so much money i have a 90 with a stock 5.0 motor what do you think, i like the way it sounds i like to scared little hondas around so let me know	stang1990	14	644	Sep 11, 2008 by stang1990
	How does this come out? (Preview) I need to take out the part in the rear above my back seat in the interior...i tried taking the seat belt things of but couldnt even get those...plus it was like 100 degrees out and i was sweaty and just didnt wanna bother with it lol...	FoxStang93	4	562	Sep 8, 2008 by FoxStang93
	help timing F cam!! (Preview) who in here runs an F cam? im havin a little trouble gettin my car to "go" it will start and idle fine, as soon as i give it some gas it hesitates and stalls...... not sure if timing is set right maybe its the carb.....any ideas?	supertukes	11	550	Sep 8, 2008 by LX546
	Cant find anywhere (Preview) been searching for days now on an article on a DIY TT set up with the two T3 turbos i have...nobody on turbomustangs.com wants to help...they basically say fuck ya self and search...but have gone through almost 50 pages of posts and found nothing...didnt know if anyone knows of any other turbo mustang...	FoxStang93	4	564	Sep 7, 2008 by FoxStang93
	heads/cam? need advice (Preview) alright well im thinking about doing the comp XE270AH cams, or cushman stage II cams(used to be VT cams) this winter if they are worth it and possibly a pair of patriot cylinder heads as well if i save up enough money. anyone know if its worth spending the 2k on these. since im in college my parents dont wan...	moddedstang1320	7	602	Sep 5, 2008 by Mineral 02
	Pads (Preview) I have decided to go with Powerslot rotors and hawk pads. Is it worth the extra $15 to buy the ceramic pads vs. the HPS??? They say the ceramic make less dust, and quieter. What would you do?	fuck bostonstangs	6	562	Sep 4, 2008 by mikefheath87
	air fuel gauge (Preview) anyone every intall one of these i got the narrow band i have to hook up the purple wire to one of the o2 sensor wires wat wires did you guys use thanks	93fox	4	597	Sep 3, 2008 by mikefheath87
	bent pushrods, cant figure it out (Preview) anybody in here got a clue why i bent my stock pushrods, i just threw on a set of GT40 heads on my 88 GT using stock HO cam, with cobra upper and lower intake, crane cams cobra 1.7 RR's, the heads are stock valves etc, the springs are new comp cams rated for .550, i threw them on with the stock rods and bent'em. i...	YoLa	11	1582	Aug 31, 2008 by Lazor
	price on machine work sound high or about right? (Preview) to get my 460 punched 030 over cam bearings cleaned freeze plugs align honed decked 900$ or do guys have any other suggestions who might be cheaper this is presician in dighton ma but im in taunton thanks	5pointslow	7	585	Aug 28, 2008 by 88stangGT
	Code P430, WTF??? (Preview) hey guys just swapped over to a UPR O/R X-pipe with the MIL's and this code popped up after 350 miles of driving it with the set-up, the codes reads P0430 Catalyst System Efficiency below Limit - Bank No 2.? is my O2 sensor shot? there are no leaks in the exhaust??? doesnt make any sense since i used to have t...	9T9MnyPit	5	605	Aug 26, 2008 by 9T9MnyPit
	re:porting and polished stock intake help!(closed) (Preview) hi guys i have a 1990 5.0 i want to port my lower intake can anybody tell how and what tools i can used i dont have a air compressor but i heard you can used a dremel tool but what else i need i want to do it myself, thanks guys. -- Edited by stang1990 at 23:20, 2008-09-09	stang1990	0	481	Aug 23, 2008 by stang1990
	power steering HELP!!!!!! (Preview) was driving and powersteering was getting crappy check fluids toped off any hints or ideas pump was replaced by ford in march 06 20k on pump HELP!!!!!!!!!!!!!!	wheels	17	640	Aug 13, 2008 by mikefheath87
	Anyone know of a logging program for a fox 5.0? (Preview) Is there any programs out there you can run on a laptop through your stock computer? Any help with this one guys?	YoLa	1	517	Aug 11, 2008 by MRicci
	Fuel line HELP!!!! (Preview) Any members out there changed there fuel lines to the braided lines? Well my 88 lx fuel line rotted away and need to install new lines but not sure on how to approach this problem. Braided lines or getting ss stock fuel line and bend myself????? Russell performance has line but not sure with all fittings...	wild88stang	3	512	Aug 9, 2008 by wild88stang
	Powerslot Rotors/Hawk Breaks (Preview) OK. After doing research and talking to members I have decided to get the Powerslot Silve Cadium Plated (non rusting/corrosion) Front AND Rear from American Muscle AND Hawk HPS (High Performance Street) Brake Pads Front and Rear from American Muscle All together with my discount I would be spendin...	fuck bostonstangs	13	615	Aug 9, 2008 by mikefheath87
	pulled cam out of my motor (Preview) i have a cam that i dont know what it is it has numbers 1206 on the front and after the distributoe gear it says ZE is this stock ....im putting my motor together and im either gonna use this or the crower 15512 cam	mikefheath87	4	556	Aug 8, 2008 by Big Frank
	GT40 heads and rocker ? (Preview) can i run stock rockers on theese heads without problems? i want to use stock vcalve covers and these rockers will not fit at all i know the cutout trick its not happening on these rockers. what are the disadvantages i will run into?	mikefheath87	3	587	Aug 8, 2008 by 12second5.0
	crowler 15512 cam (Preview) just bought a motor. guy siad it was a 306 but its not. it has a crowler 15512. anyone have them how are they? am i beter off with anything elce? i hope this one works well for what i have... cobra intake gt40 heads 24lb inj.	mikefheath87	5	632	Aug 5, 2008 by mikefheath87
	free car manuals (Preview) Found this and had to share........ Step 1: go to http://www.bedlib.org/ebsco.html Step 2: click on the ARRC logo near the top Step 3: under "user id" type "user" and under "password" type "password" Step 4: scroll to the bottom, and press the AAR...	uatlb	11	793	Jul 29, 2008 by Lazor
	S/C update (Preview) ok guys i finally got the s trim and i want to install it on my pos motor for about a months or two....i still need bigger inj so if anyone has em let me know. so for those of you who have done this any heads up on something specific on what i should or shouldn't do. Any input is greatly appreciated. -- Edited by m...	mikefheath87	31	1318	Jul 24, 2008 by TFStang
	Need some serious help (Preview) I finally got all the parts i needed and installed them. New head gaskets, upper and lower intake water pump, and headers. I just got it all 2gether about 20 min ago and when the car starts its knocking and shaking like a bastard. any ideas on whats up with it	TAPorSNAP	28	1123	Jul 23, 2008 by Lazor
	351...what do i need (Preview) After talkin to a few people it seems a 351 project into a 408 stroker seems to be the way i want to go and its the most realistic goal i can reach right now...what do i need to do as far as motor mounts...tranni...intake...carb...all that stuff...thanks	FoxStang93	4	624	Jul 21, 2008 by TFStang
	idle hanging (Preview) so last night very long night i installed a or h pipe and a cat back and now wheni come to a stop the idle stays at about 1k for a couple of seconds i have yet to put the mil elims in caise i needed extensions for the o2's so is it cause the ses light is or else what do i do here thanks	bleed blue	8	686	Jul 19, 2008 by bleed blue
	got 460 today and is huge no one was lying about that lol (Preview) thanks to all on tech questions about it even know i got to prove to half of u guys that it will work lol jk guys thanx a bunch once lifts in everyone welcome to use	5pointslow	0	494	Jul 18, 2008 by 5pointslow
	bought 460 picking up tomorrow what springs for front? seriously!paid 100$ (Preview) need to get an idea on front springs ...laugh 460 i know blah blah hope u guys respect my plans because i would do the same to you guys and i want to be alittle diffrent thanks again mineral02,retro5.0,12second5.0 aka larry for all the help with my dumb ass -- Edited by 5pointslow at 17:36, 2008-07-17 -- E...	5pointslow	31	968	Jul 18, 2008 by 5pointslow
	just got 4 cylinder notch and want motor opinions (Preview) efi stock block 302 turbo carb but same as above or 351 windsor to 408 carb with turbo or go same with efi or fuck it just slap a 460 and c6 in it and throw the a 250 shot of spray whats your guys opinions got money to do any way not gonna be daily driven an is gonna be an auto a week end car to beat on put my foot throug...	5pointslow	18	816	Jul 16, 2008 by Big Frank
	aluminum heads (Preview) i have a 94 cobra with gt40 heads on it and some 1.7's. looking at patriot performance aluminum heads but want to know what size i should get. don't want to really cut pistons and don't want to order get and install to find out i have clearence isues. a set of heads are under $1000. i know someone with then an...	andyss420	5	553	Jul 16, 2008 by Big Frank
	cam degree (Preview) the numbers on the lower sprocket...302 w/crowler 15512 set it at the original timing mark or advance or retard anything? the sprocket is labeled all the way around. car is going to be s/c. anything helps thanks.	mikefheath87	2	523	Jul 15, 2008 by mikefheath87
	Brakes/Rotors (Preview) Within the next month I am due for new brakes and rotors. I have heard many different things. I am looking for drilled and slotted rotors that DON'T RUST, along with decent brake pads. Anyone have any advice on which to buy? Which NOT to buy? I would not like to spend a ton of money on them but at the same time...	fuck bostonstangs	3	589	Jul 15, 2008 by wheels
	heads (Preview) which heads are better or id there even a difference the romeo or windsor all i know right now is the valve covers are diffrent	bleed blue	2	512	Jul 13, 2008 by bleed blue
	blower question (Preview) what can a stock 2v hod for hp and boost i would like to supercharge it but dont want to pop it so what are some safe numbers and what kind of power am i looking also would like to do it as a complete kit	bleed blue	13	695	Jul 12, 2008 by Nick Papageorgio
«First < 1 2 3 4 5 6 7 8 > Last» \| Page of 8 sorted by