BOSTONSTANGS.COM

TAPorSNAP · TAPorSNAP

I really need some help on this 1. I have been searching for an hour now and couldnt find what im looking for....maybe some1 has the answer on here... I have my stock fuel lines on my 88 gt. I am switching to aftermarket high flow fuel rails. I need a fitting to go from the stock lines and turns it into A-N fi...

bleed blue · bleed blue

just like the title says what the difference between the two am i better of with an x pipe or h pipe no cats

flamingpony83 · flamingpony83

i got a brand new kit cheap so i figure i install it. but i hear if it has abs i need 2 kits...is it true?

TAPorSNAP · TAPorSNAP

Im not sure how to really explain it, But I will try.... On the front of the lower intake manifold, there are the pipes that go to the heater core and also has the takeoffs to go to the egr spacer. I was wondering if it is possible to completely take those metal tubes out and plug the whole since I will be byp...

TAPorSNAP · TAPorSNAP

I just put my heads back on after putting on new head gaskets, and I was wondering if any1 knows how to adjust the pushrods with the pedestal mount rockers

mustang50lx88 · mustang50lx88

Ok I am having yet another issue.. Where my Starter Relay is there is the Negative wire going to it then, the positive. I have a problem with the positive side.. the wires on there have fusible links and one of the wires broke off from the connector... How do I go about replacing the fusible link, and what a...

5pointslow · 5pointslow

never been heard good things good/ with n2o or blower cars? and does he have a dyno and located where? leonards is probaly not so convnient after all lol

5pointslow · 5pointslow

with a good clutch could it hand a 302 with 300-400 hp a 351 with crazy power what is the opinions

89Rustang · 89Rustang

Anyone have one I can borrow to cut the reliefs on my pistons for 2.02 valves? The one that you can use while pistons are in the block. Thx.

mustang50lx88 · mustang50lx88

I dont know what happened.. I was making a right turn into a store parking lot and all of a sudden I hear this sound as if metal is dragging on the pavement.. I then quickly pulled off to the side and stopped and took a look underneith the car.. couldn't find anything visually wrong.. The weird thing is I can...

TAPorSNAP · TAPorSNAP

I just blew my head gasket over the weekend and I decided that since I am taking everything off to replace them, I might as well upgrade. I found a site to get some gt 40 heads assembled. so i was wondering if anyone knows what I have to do about getting new rockers and pushrods. What kind and size I should get...

fuck bostonstangs · fuck bostonstangs

Did a little research on my tuner and came across this: It is funny to think that twenty years ago, when Ford Mustangs were introduced with computer controlled engine systems, many people felt it signified the end of hot rodding. "EFI and EEC controlled engines will be too complicated for the...

flamingpony83 · flamingpony83

i bought a 6al and the guy gave me a brand new adj timing control free. anyone have it. does it make things easier or what? let me know what you think about it.

mustang50lx88 · mustang50lx88

Well I was bleeding my brakes the other day because the back drivers side line was replaced.. So anyways when I went to go and bleed the line on that side, I noticed the Bleeder valve was stripped to shit, probably from the rust or previous owner, So I went on bleeding the other ones which were fine, and I go...

5pointslow · 5pointslow

was curious i no turbos love a load on motor but powerglide on street gonna build 408 over winter and tossing idea of a turbo and i no the t5 wont hold so was wondering in put and its not daily driven

93 LX FiveO · 93 LX FiveO

new plugs, new cap, new rotor, new wires, new throttle body, new mass air. tps has been adjusted to .9 volts car hesitates when stabbing gas in gear. in neutral it revs very smooth car also has adjustable fpr which is set @ 35psi *vac on / 42psi *vac off new 02 sensors as well, with an off-road pi...

SPDoherty · SPDoherty

Before I get flamed I want you guys to know that this idea only going to be chased AFTER my car is one color and etc. So I know I want to make my car a whole shitload faster but I can't decide what would be the best bet. So basically I kinda want this forum to be an open one for all suggestions. I want to know what yo...

tom00769 · tom00769

I have always felt a small vibration but not bad. This weekend I was fucking around with a gto on the highway. At 120 I thought the car was going to fall apart. Above that speed it was ok again. Could it be u-joints or is it the drive shaft it self?

flamingpony83 · flamingpony83

i have had many mustangs and have done many motors, but i have never installed adj stud rockers and i have never had to measure for push rods. i would like to know what im doing before i start something. so if anyone could give me a hand that would be awsome. i just dont want to fuck anything up in my new motor....

5 oh · 5 oh

does anyones else's roller rockers sound like a sewing machine when the engine is running? i just started my motor today with the crane cam 1.7's and its kinda loud is it normal?

moddedstang1320 · moddedstang1320

today i get up and start driving to the gas station and on the way i realize my car is acting funny. i will be driving in 3rd or 4th then come to a stop light and engage the clutch and put it in neutral and the rpms raise to 2500 and stay there for around 10 seconds then suddenly drop and it even stalled once when i...

dexx · dexx

got an 87 gt just bought a high torque starter problem is only one starter wire on old one and i hooked up new starter where i believe i should of but got nothing there is another connection on starter solenoid but its like an electrical connection anyone know what might be problem???maybe wrong starter...

5pointslow · 5pointslow

90 lx pro 50 shifter smog/ac delete stock short block tfs stage 1 cam tfs trackheat intake 70mm tb 24lb injectors tfs twisted wedge heads 1.6 roller rockers 373s nitto drag radials wet 150 shot of juice and its a nx kit and nx kits are rated at rear wheel nx tech guy said so and they advertise t...

montey04 · montey04

i have a 93 lx with mac equal length headers i keep melting spark plug wire boots on the driver side last two cylinders i have the motorsport 9.5 wires now need to buy new ones wanted to know if any of you guys have had this happen to you and what kind of wires are you using now thanks

5pointslow · 5pointslow

they have a md dyno which if u do the reasearch way more acurate than a dyno jet this is a very very nice setup my brother already put his camaro on it 100$ 3 pulls -- Edited by 5pointslow at 19:58, 2008-04-23 -- Edited by 5pointslow at 21:11, 2008-04-23

shadybrady · shadybrady

i need help hooking up a switch for my battery because its in the back of my car if any one knows let me know how to do it thanxs

ls1 our savior · ls1 our savior

Anyone know where to buy a dial indicator around the south shore area?

SKEETER_SVT01 · SKEETER_SVT01

Well, my clutch its beyond horrible, Its funny to look at. I will take pics later on. I also destroyed the flywheel And..... blew another set of bassani cats. 3rd set Instead of the RAM900, decided to get the Centerforce DFX clutch Ford Racing Billet Alum fly wheel Bassnai race tubes. Car will be loud an...

fuck bostonstangs · fuck bostonstangs

When I start my car most of the time there is a rattle/ knocking/ticking noise within the engine but it will go away by the time you count to 3. I can't figure out what it may be. It only happens sometimes when i start it, along with that it doesnt always start the click of the key like it used too a few months ag...

mustang50lx88 · mustang50lx88

As I was doing an Oil Change and had my car up on the lift @ work, I was just making some checks on things while I was under the car.. I noticed that my front sway bar moves a little bit.. It's bolted up and bolts are not loose, but I believe the bushings are old and in need of replacement.. I was looking around 50...

5pointslow · 5pointslow

http://www.edquay.com/shop/product_info.php?products_id=95&osCsid=e3ef69f20de7a160b53a9086fb20818f

Greekstang · Greekstang

My car has been sitting for the last two months after blowing a spark plug out. I threw the plug back in with a helicoil but it's not sitting in there right. I bought a replacement head but I'm hoping someone can just re-thread the current one and do a lot better job than I did. I'm calling someone tomorro...

jgt8229 · jgt8229

hi, i got a 89 stang 5.0 , i am having a problem. whenm i start up my car my oil psi runs about normals or a little under half way, then when it heats up it jus drops all the wayy bellow zero, if i revvv it it will rise to about 10 psi then drop way below zero again once the revvs go down. my temp gauge is broke its belo...

fast2000mustanggt · fast2000mustanggt

looking to put a clutch in 00 gt whats good whats not..? -- Edited by fast2000mustanggt at 16:35, 2008-05-26

88stangGT · 88stangGT

Sup guys, haven't been on much since i haven't had my car on the road, but i'm finally putting my car on the road after a long winter. Anyway, i've got an 88gt 5.0 with some trickflow heads,trick flow track heat cam with 5.10 lift, full roller, edelbrock performer upper and lower, bbk 65mm throttle body,...

9greeNotch3 · 9greeNotch3

Well all my lights used to work...took my dash out to do my heater core and put white face gauges in...put it alll back together...headlights and the lights on the right side of my dash dont work...the steering column is out so allll the wires that connect to the steering column are unplugged...well i c...

9greeNotch3 · 9greeNotch3

I saw last year in MM&FF a kit for notchs and verts to have lift supports in your trunk to replace the bar set up thats factory...really nice clean looking kit but cant find it anywhere...anyone seen this around? has the brackets and lift supports and everythin in aluminum....AND NOW I FOUND IT......

9greeNotch3 · 9greeNotch3

Wondering if anyone is running the same set up and how long of a belt i need...stock pulleys...alternator, stock tensioner, crank pulley, and power steering pump...no air pump and no a/c compressor...

9greeNotch3 · 9greeNotch3

anyone ever heard of these? have a set to sell but have no clue/info on them...they came out of a 10 sec fox body...just the lowers in mint/new shape...price? pics? thanks

91chrisgt · 91chrisgt

hey guys need help very bad , i keep loseing my belt and i figured out why , but don't know how to fix it , my alternator is sitting cocked alittle bit , not sure if i even have the right lower bracket. i tried shimming it and the bracket cracked! i only have 3 pulley's alt. crank, and water pump , so the upper alt...

qwik88 · qwik88

any one know if you can install a mini spool with out pulling the carrier??

mustang50lx88 · mustang50lx88

I have a 1988 Mustang 5.0 LX.. The problem I'm running into is, When I went to start up the car the starter made a grinding noise and still didn't start, you know, the sound it makes when the car is already running and you accidently turn the key all the way and then you hear that grinding noise, yeah that sou...

9greeNotch3 · 9greeNotch3

Well finally got my new clutch in everything bolted up ready to go...but like last year when i put a new clutch in and a new cable...it wont fully disengage...so my car either will grind or not go into gear without a fight...its fully adjusted and everything...i still have a stock quadrant and everythi...

luke · luke

i purchased a used tubular k member wich came with a flammin river steering rack so i pulled the power steering pump out but i cant find a reliable way 2 run the belt. i have it going over the idler pulley the wrong way (grooved side down) but i would like 2 c how other people have tackled this problem without...

irishboom2 · irishboom2

Was installing my clutch only to notice that my subframe connector welding had broken on the passenger side...had to cut the old weld,break the sf conn off the car,grind it down and finally re-weld it in place...what a bitch but at least it is done right this time...will take pics tomorrow of the new we...

mustang50lx88 · mustang50lx88

I just noticed the other day that I'm leaking tranny fluid from where the speedo gear connects to the tranny. It's not too severe of a leak but has a slow leak from there.. What should I do to fix that? Please Help, thanks to those who reply.

93 LX FiveO · 93 LX FiveO

i got 21, 33, 41, 91, 94, and a couple more i cant remember 21 is ect out of range (car was cold during test) 33 is egr not opening 41 is HEGO something, running too lean?? 91 is fuel pump secondary circuit failure to pcm.. wtf does that mean? 94 is air thermactor not functional (stupid smog shit) a...

boostd710 · boostd710

So as my 90 Hatch was in the shop for head gaskets, my mechanic noticed that my frame by my strut towers is rotting out and he refuses to put my motor back together until my car gets welded up... Now i have called so many autobody shops as well as welders and they all say "I cant help you." So now I am...

supertukes · supertukes

seal blew out of the steering box, fixed that, now the cap keeps blowin off the pump, brand new lines so those arent causing any extra pressure, any ideas? pump junk probably? its a 6cyl 2wd

mustang50lx88 · mustang50lx88

I just bought a New Speedo Gear Retaing Clip.. cuz mine was missing apparently, so I bought a new one... Now I'm having a problem as to where it goes exactly... can anyone show me a pic or something and help me out... It's probably easy but just want to make sure its going in the right spot... here is a pic of t...

Topic		Started By	Replies	Views	Last Post
	Fuel Line Fittings...Really pissin me off !!!!!! (Preview) I really need some help on this 1. I have been searching for an hour now and couldnt find what im looking for....maybe some1 has the answer on here... I have my stock fuel lines on my 88 gt. I am switching to aftermarket high flow fuel rails. I need a fitting to go from the stock lines and turns it into A-N fi...	TAPorSNAP	5	502	Jul 12, 2008 by 12second5.0
	x or h (Preview) just like the title says what the difference between the two am i better of with an x pipe or h pipe no cats	bleed blue	19	715	Jul 12, 2008 by Mineral 02
	anyone ever install line lock? (Preview) i got a brand new kit cheap so i figure i install it. but i hear if it has abs i need 2 kits...is it true?	flamingpony83	28	4090	Jul 11, 2008 by flamingpony83
	Getting rid of heater core (Preview) Im not sure how to really explain it, But I will try.... On the front of the lower intake manifold, there are the pipes that go to the heater core and also has the takeoffs to go to the egr spacer. I was wondering if it is possible to completely take those metal tubes out and plug the whole since I will be byp...	TAPorSNAP	1	468	Jul 10, 2008 by 12second5.0
	Pushrods (Preview) I just put my heads back on after putting on new head gaskets, and I was wondering if any1 knows how to adjust the pushrods with the pedestal mount rockers	TAPorSNAP	4	524	Jul 8, 2008 by TAPorSNAP
	Fusible Links (Preview) Ok I am having yet another issue.. Where my Starter Relay is there is the Negative wire going to it then, the positive. I have a problem with the positive side.. the wires on there have fusible links and one of the wires broke off from the connector... How do I go about replacing the fusible link, and what a...	mustang50lx88	1	493	Jul 8, 2008 by mustang50lx88
	Hows dez racing?? good or bad?? (Preview) never been heard good things good/ with n2o or blower cars? and does he have a dyno and located where? leonards is probaly not so convnient after all lol	5pointslow	22	3899	Jul 8, 2008 by TFStang
	lets get some opinions on how much can a stock t5 handle?? (Preview) with a good clutch could it hand a 302 with 300-400 hp a 351 with crazy power what is the opinions	5pointslow	27	908	Jul 8, 2008 by 89Rustang
	Valve relief cutter (Preview) Anyone have one I can borrow to cut the reliefs on my pistons for 2.02 valves? The one that you can use while pistons are in the block. Thx.	89Rustang	2	855	Jul 7, 2008 by 93_REEF_NOTCH
	Somethings wrong with the front end of my Stang.. Please Help (Preview) I dont know what happened.. I was making a right turn into a store parking lot and all of a sudden I hear this sound as if metal is dragging on the pavement.. I then quickly pulled off to the side and stopped and took a look underneith the car.. couldn't find anything visually wrong.. The weird thing is I can...	mustang50lx88	11	607	Jul 7, 2008 by 12second5.0
	HEADS (Preview) I just blew my head gasket over the weekend and I decided that since I am taking everything off to replace them, I might as well upgrade. I found a site to get some gt 40 heads assembled. so i was wondering if anyone knows what I have to do about getting new rockers and pushrods. What kind and size I should get...	TAPorSNAP	8	628	Jul 7, 2008 by 12second5.0
	Diablosport Predator Tuner (Preview) Did a little research on my tuner and came across this: It is funny to think that twenty years ago, when Ford Mustangs were introduced with computer controlled engine systems, many people felt it signified the end of hot rodding. "EFI and EEC controlled engines will be too complicated for the...	fuck bostonstangs	0	625	Jul 7, 2008 by fuck bostonstangs
	adjustable timing control (Preview) i bought a 6al and the guy gave me a brand new adj timing control free. anyone have it. does it make things easier or what? let me know what you think about it.	flamingpony83	3	533	Jul 6, 2008 by 12second5.0
	Brake Bleeder Screw Stripped.. Need Help (Preview) Well I was bleeding my brakes the other day because the back drivers side line was replaced.. So anyways when I went to go and bleed the line on that side, I noticed the Bleeder valve was stripped to shit, probably from the rust or previous owner, So I went on bleeding the other ones which were fine, and I go...	mustang50lx88	14	817	Jul 6, 2008 by FoxStang93
	powerglide tranny on street heard turbo cars love em?? any input (Preview) was curious i no turbos love a load on motor but powerglide on street gonna build 408 over winter and tossing idea of a turbo and i no the t5 wont hold so was wondering in put and its not daily driven	5pointslow	2	513	Jul 4, 2008 by notchdan
	whys my car stumbling? (Preview) new plugs, new cap, new rotor, new wires, new throttle body, new mass air. tps has been adjusted to .9 volts car hesitates when stabbing gas in gear. in neutral it revs very smooth car also has adjustable fpr which is set @ 35psi vac on / 42psi vac off new 02 sensors as well, with an off-road pi...	93 LX FiveO	5	600	Jun 27, 2008 by 93 LX FiveO
	New motor (Preview) Before I get flamed I want you guys to know that this idea only going to be chased AFTER my car is one color and etc. So I know I want to make my car a whole shitload faster but I can't decide what would be the best bet. So basically I kinda want this forum to be an open one for all suggestions. I want to know what yo...	SPDoherty	20	769	Jun 25, 2008 by Big Frank
	vibration in drivetrain (Preview) I have always felt a small vibration but not bad. This weekend I was fucking around with a gto on the highway. At 120 I thought the car was going to fall apart. Above that speed it was ok again. Could it be u-joints or is it the drive shaft it self?	tom00769	7	550	Jun 25, 2008 by stang91
	HELP! (Preview) i have had many mustangs and have done many motors, but i have never installed adj stud rockers and i have never had to measure for push rods. i would like to know what im doing before i start something. so if anyone could give me a hand that would be awsome. i just dont want to fuck anything up in my new motor....	flamingpony83	1	526	Jun 23, 2008 by GTStang
	roller rocker noise (Preview) does anyones else's roller rockers sound like a sewing machine when the engine is running? i just started my motor today with the crane cam 1.7's and its kinda loud is it normal?	5 oh	2	620	Jun 22, 2008 by Big Frank
	somethings wrong with my car (Preview) today i get up and start driving to the gas station and on the way i realize my car is acting funny. i will be driving in 3rd or 4th then come to a stop light and engage the clutch and put it in neutral and the rpms raise to 2500 and stay there for around 10 seconds then suddenly drop and it even stalled once when i...	moddedstang1320	7	514	Jun 17, 2008 by moddedstang1320
	starter help (Preview) got an 87 gt just bought a high torque starter problem is only one starter wire on old one and i hooked up new starter where i believe i should of but got nothing there is another connection on starter solenoid but its like an electrical connection anyone know what might be problem???maybe wrong starter...	dexx	1	490	Jun 15, 2008 by Pitbull11
	what do u think it will run ?? (Preview) 90 lx pro 50 shifter smog/ac delete stock short block tfs stage 1 cam tfs trackheat intake 70mm tb 24lb injectors tfs twisted wedge heads 1.6 roller rockers 373s nitto drag radials wet 150 shot of juice and its a nx kit and nx kits are rated at rear wheel nx tech guy said so and they advertise t...	5pointslow	19	807	Jun 14, 2008 by 01SilverGt
	spark plug wires melting (Preview) i have a 93 lx with mac equal length headers i keep melting spark plug wire boots on the driver side last two cylinders i have the motorsport 9.5 wires now need to buy new ones wanted to know if any of you guys have had this happen to you and what kind of wires are you using now thanks	montey04	3	612	Jun 11, 2008 by Mustswang
	leonards performance in taunton has a dyno now (Preview) they have a md dyno which if u do the reasearch way more acurate than a dyno jet this is a very very nice setup my brother already put his camaro on it 100$ 3 pulls -- Edited by 5pointslow at 19:58, 2008-04-23 -- Edited by 5pointslow at 21:11, 2008-04-23	5pointslow	21	1197	Jun 11, 2008 by Hissing Cobra
	i need help hooking up a power cut off switch for my battery (Preview) i need help hooking up a switch for my battery because its in the back of my car if any one knows let me know how to do it thanxs	shadybrady	8	506	Jun 7, 2008 by stang91
	dial indicator (Preview) Anyone know where to buy a dial indicator around the south shore area?	ls1 our savior	3	480	Jun 7, 2008 by ls1 our savior
	Latest clutch news (Preview) Well, my clutch its beyond horrible, Its funny to look at. I will take pics later on. I also destroyed the flywheel And..... blew another set of bassani cats. 3rd set Instead of the RAM900, decided to get the Centerforce DFX clutch Ford Racing Billet Alum fly wheel Bassnai race tubes. Car will be loud an...	SKEETER_SVT01	6	584	Jun 6, 2008 by SKEETER_SVT01
	rattling/knocking noise? (Preview) When I start my car most of the time there is a rattle/ knocking/ticking noise within the engine but it will go away by the time you count to 3. I can't figure out what it may be. It only happens sometimes when i start it, along with that it doesnt always start the click of the key like it used too a few months ag...	fuck bostonstangs	15	772	Jun 5, 2008 by SKEETER_SVT01
	Front Sway Bar (Preview) As I was doing an Oil Change and had my car up on the lift @ work, I was just making some checks on things while I was under the car.. I noticed that my front sway bar moves a little bit.. It's bolted up and bolts are not loose, but I believe the bushings are old and in need of replacement.. I was looking around 50...	mustang50lx88	0	426	Jun 5, 2008 by mustang50lx88
	ED QUAY aluminum wings on mustang ??? how they look? (Preview) http://www.edquay.com/shop/product_info.php?products_id=95&osCsid=e3ef69f20de7a160b53a9086fb20818f	5pointslow	4	2016	Jun 1, 2008 by 96SLOBRA
	Might need a mechanic (Preview) My car has been sitting for the last two months after blowing a spark plug out. I threw the plug back in with a helicoil but it's not sitting in there right. I bought a replacement head but I'm hoping someone can just re-thread the current one and do a lot better job than I did. I'm calling someone tomorro...	Greekstang	5	528	May 31, 2008 by Autoteknix
	oil presure!!!! (Preview) hi, i got a 89 stang 5.0 , i am having a problem. whenm i start up my car my oil psi runs about normals or a little under half way, then when it heats up it jus drops all the wayy bellow zero, if i revvv it it will rise to about 10 psi then drop way below zero again once the revvs go down. my temp gauge is broke its belo...	jgt8229	9	635	May 30, 2008 by qwik88
	clutch (Preview) looking to put a clutch in 00 gt whats good whats not..? -- Edited by fast2000mustanggt at 16:35, 2008-05-26	fast2000mustanggt	9	687	May 28, 2008 by fast2000mustanggt
	331 stroker (Preview) Sup guys, haven't been on much since i haven't had my car on the road, but i'm finally putting my car on the road after a long winter. Anyway, i've got an 88gt 5.0 with some trickflow heads,trick flow track heat cam with 5.10 lift, full roller, edelbrock performer upper and lower, bbk 65mm throttle body,...	88stangGT	6	585	May 24, 2008 by 88stangGT
	Lighting Problems (Preview) Well all my lights used to work...took my dash out to do my heater core and put white face gauges in...put it alll back together...headlights and the lights on the right side of my dash dont work...the steering column is out so allll the wires that connect to the steering column are unplugged...well i c...	9greeNotch3	10	582	May 23, 2008 by mustang50lx88
	ATTN: NOTCHBACKS!!!! (Preview) I saw last year in MM&FF a kit for notchs and verts to have lift supports in your trunk to replace the bar set up thats factory...really nice clean looking kit but cant find it anywhere...anyone seen this around? has the brackets and lift supports and everythin in aluminum....AND NOW I FOUND IT......	9greeNotch3	3	577	May 22, 2008 by 9greeNotch3
	BELT LENGTH (Preview) Wondering if anyone is running the same set up and how long of a belt i need...stock pulleys...alternator, stock tensioner, crank pulley, and power steering pump...no air pump and no a/c compressor...	9greeNotch3	4	528	May 21, 2008 by 9greeNotch3
	SSM control arms? (Preview) anyone ever heard of these? have a set to sell but have no clue/info on them...they came out of a 10 sec fox body...just the lowers in mint/new shape...price? pics? thanks	9greeNotch3	9	813	May 21, 2008 by 9greeNotch3
	alternator bracket (Preview) hey guys need help very bad , i keep loseing my belt and i figured out why , but don't know how to fix it , my alternator is sitting cocked alittle bit , not sure if i even have the right lower bracket. i tried shimming it and the bracket cracked! i only have 3 pulley's alt. crank, and water pump , so the upper alt...	91chrisgt	6	546	May 19, 2008 by 91chrisgt
	mini spool ?? (Preview) any one know if you can install a mini spool with out pulling the carrier??	qwik88	0	472	May 17, 2008 by qwik88
	*Starting Issues Please Help* (Preview) I have a 1988 Mustang 5.0 LX.. The problem I'm running into is, When I went to start up the car the starter made a grinding noise and still didn't start, you know, the sound it makes when the car is already running and you accidently turn the key all the way and then you hear that grinding noise, yeah that sou...	mustang50lx88	15	670	May 16, 2008 by uatlb
	CLUTCH WONT FULLY DISENGAGE (Preview) Well finally got my new clutch in everything bolted up ready to go...but like last year when i put a new clutch in and a new cable...it wont fully disengage...so my car either will grind or not go into gear without a fight...its fully adjusted and everything...i still have a stock quadrant and everythi...	9greeNotch3	42	1009	May 15, 2008 by 9greeNotch3
	serpintine issues (Preview) i purchased a used tubular k member wich came with a flammin river steering rack so i pulled the power steering pump out but i cant find a reliable way 2 run the belt. i have it going over the idler pulley the wrong way (grooved side down) but i would like 2 c how other people have tackled this problem without...	luke	4	524	May 10, 2008 by 93 LX FiveO
	Talk about a find... (Preview) Was installing my clutch only to notice that my subframe connector welding had broken on the passenger side...had to cut the old weld,break the sf conn off the car,grind it down and finally re-weld it in place...what a bitch but at least it is done right this time...will take pics tomorrow of the new we...	irishboom2	2	483	May 8, 2008 by Mustswang
	*Help Leaking Tranny Fluid* (Preview) I just noticed the other day that I'm leaking tranny fluid from where the speedo gear connects to the tranny. It's not too severe of a leak but has a slow leak from there.. What should I do to fix that? Please Help, thanks to those who reply.	mustang50lx88	6	573	May 2, 2008 by mustang50lx88
	codes list (Preview) i got 21, 33, 41, 91, 94, and a couple more i cant remember 21 is ect out of range (car was cold during test) 33 is egr not opening 41 is HEGO something, running too lean?? 91 is fuel pump secondary circuit failure to pcm.. wtf does that mean? 94 is air thermactor not functional (stupid smog shit) a...	93 LX FiveO	2	538	May 1, 2008 by Geevaaa9112
	HELP!! Need Welding ASAP! (Preview) So as my 90 Hatch was in the shop for head gaskets, my mechanic noticed that my frame by my strut towers is rotting out and he refuses to put my motor back together until my car gets welded up... Now i have called so many autobody shops as well as welders and they all say "I cant help you." So now I am...	boostd710	5	538	Apr 29, 2008 by 03gt92hatch
	f150 p/s pump (Preview) seal blew out of the steering box, fixed that, now the cap keeps blowin off the pump, brand new lines so those arent causing any extra pressure, any ideas? pump junk probably? its a 6cyl 2wd	supertukes	3	515	Apr 27, 2008 by mikefheath87
	Where does this Speedo Retaining Clip Go????? HELP! (Preview) I just bought a New Speedo Gear Retaing Clip.. cuz mine was missing apparently, so I bought a new one... Now I'm having a problem as to where it goes exactly... can anyone show me a pic or something and help me out... It's probably easy but just want to make sure its going in the right spot... here is a pic of t...	mustang50lx88	6	494	Apr 26, 2008 by mustang50lx88
«First < 1 … 4 5 6 7 8 > Last» \| Page of 8 sorted by